Glidecoat MAX

Glidecoat MAX is a self-leveling ceramic coating designed to increase durability by providing the thickest protective layer possible from a ceramic coating! The unique Glidecoat MAX formula eliminates the need for hand-buffing or leveling the coating with a microfiber cloth. This allows the coating to cure at its MAXimum coating thickness - 10 times thicker than a standard ceramic coating - 20 microns in thickness versus 1-2 microns. The added thickness dramatically increases durability and allows it to be used under the water line.

CAUTION

  • Wear protective gloves and eye gear.
  • Keep away from heat and open flames.
  • Do not smoke when using.
  • Keep container tightly sealed.
  • Store in well-ventilated area.

APPLICATION INSTRUCTIONS

IT IS VERY IMPORTANT THAT YOU FOLLOW THE PROVIDED INSTRUCTIONS FOR ALL GLIDECOAT PRODUCTS.

Note:
Before applying Glidecoat MAX, ensure the surface of your boat has been fully prepped, including cleaning, removal of any marine organisms, dirt, salt scum or other surface contaminants to ensure a consistent surface. If the surface has oxidation, this must be removed with a machine buffer and a compound before applying Glidecoat MAX. For optimal results, Glidecoat MAX should be applied to a clean, glossy surface. Prior to application of the coating, wipe down the clean prepped surface with Glidecoat Surface Wipe or Isopropyl Alcohol to remove any lingering oils or contaminants.

  • Using the provided pipette, apply 2-3ml of Glidecoat MAX to the application sponge. Working in a 4ft x 4ft section, apply Glidecoat MAX using an up-and-down, then side-to-side pattern, ensuring the entire section is evenly covered with coating. If even coverage is not achieved in this first pass, quickly add more Glidecoat MAX to the application sponge and go over the section again to achieve consistency. Glidecoat MAX will begin to self-level within 15-30 seconds, creating a smooth and uniform appearance.
  • While the previous section is still wet, within 1-2 minutes, repeat step 1 on your next section, overlapping slightly with your previous section. It is important to move from section to section while the previously applied coating is still wet to allow the coating to self-level properly. Once previously applied sections of coating have dried - approximately 5 minutes - you will no longer be able to overlap the coating. The coating will not level properly on the dried coating, which will cause high spots and inconsistencies in the finish.
  • Continue applying the coating in 4x4 sections in a non-stop fashion until one side of the hull is completely coated or you have reached a definitive break point in the hull (such as a chine line).
  • Only one coat of Glidecoat MAX is required. Multiple coats cannot be applied!
  • Allow 24 hours of cure time before splashing the boat in the water.

STORAGE

  • Shelf life unopened is 1 year.
  • Once the bottle has been opened, the product should be used within 30 days.
  • Store product with cap fully sealed.
  • To extend the shelf life after opening, store the sealed bottle in the freezer.
  • If the product is in liquid form, it is good to use. When the shelf life is past, the liquid in the bottle will solidify, and is no longer able to be applied.

TECHNICAL DATA

  • Shelf life unopened is 1 year.
  • Once the bottle has been opened, the product should be used within 30 days.
  • Store product with cap fully sealed.
  • To extend the shelf life after opening, store the sealed bottle in the freezer.
  • If the product is in liquid form, it is good to use. When the shelf life is past, the liquid in the bottle will solidify, and is no longer able to be applied.

DISCLAIMER

Note:
Before applying Glidecoat MAX, ensure the surface of your boat has been fully prepped, including cleaning, removal of any marine organisms, dirt, salt scum or other surface contaminants to ensure a consistent surface. If the surface has oxidation, this must be removed with a machine buffer and a compound before applying Glidecoat MAX. For optimal results, Glidecoat MAX should be applied to a clean, glossy surface. Prior to application of the coating, wipe down the clean prepped surface with Glidecoat Surface Wipe or Isopropyl Alcohol to remove any lingering oils or contaminants.