Revestimiento Cerámico para motocicletas

$59.95

Mantener tu motocicleta limpia y brillante es un punto de orgullo para muchos propietarios. Pero las motocicletas presentan una serie de retos únicos incluso para los detallistas más expertos: la variedad de superficies, los contornos y las zonas de difícil acceso, las superficies de alta temperatura, por no mencionar los insectos, la grasa, la suciedad de la carretera y otros contaminantes ambientales. Glidecoat ha desarrollado nuestro revestimiento cerámico para motocicletas pensando en los entusiastas del bricolaje: un revestimiento que se puede utilizar en todas las superficies duras, es fácil de aplicar y mantener, y ofrece una protección inigualable contra los rayos UV, la corrosión, las manchas, los contaminantes de la carretera y mucho más.

Incluye:

  • 30 ml de revestimiento cerámico para motocicleta
  • 1 Aplicador de cerámica
  • 1 Par de Guantes de Protección
  • Description

    Lo último en protección de superficies

    Mantener tu motocicleta limpia y brillante es un punto de orgullo para muchos propietarios. Pero las motocicletas presentan una serie de retos únicos incluso para los detallistas más expertos: la variedad de superficies, los contornos y las zonas de difícil acceso, las superficies de alta temperatura, por no mencionar los insectos, la grasa, la suciedad de la carretera y otros contaminantes ambientales. Glidecoat ha desarrollado nuestro revestimiento cerámico para motocicletas pensando en los entusiastas del bricolaje: un revestimiento que se puede utilizar en todas las superficies duras, es fácil de aplicar y mantener, y ofrece una protección inigualable contra los rayos UV, la corrosión, las manchas, los contaminantes de la carretera y mucho más.

    Glidecoat ha sido sometido a extensas pruebas de campo en condiciones extremas por parte de laboratorios independientes acreditados y se ha demostrado que proporciona al menos 3 años de protección incluso en las condiciones más duras. Además, en “condiciones medias” y con un mantenimiento y cuidado adecuados, los resultados de nuestro revestimiento cerámico, en algunos casos, han superado este mínimo de 3 años.

    Fácil de aplicar:
    Nuestro revestimiento cerámico para motocicletas está diseñado para el usuario DIY (Bricolaje). No requiere ningún equipo especializado para aplicarlo, como pulverizadores, máquinas aplicadoras o lámparas de calor/UV para curar. Simplemente pase la esponja de aplicación incluida y luego pula inmediatamente con un paño de microfibra limpio. Deja que se cure entre 24 y 48 horas antes de mojarlo y tu moto estará protegida durante 3 años.

    Cerámica vs. cera de Glidecoat:
    Aunque la cera es el método tradicional de protección de superficies, la verdad es que la cera pierde su funcionalidad superficial en cuestión de semanas. La cera simplemente se asienta en la superficie y se elimina fácilmente por abrasión. Esto significa que cada vez que se lava la moto o se la saca a pasear, se elimina parte de la cera. La mayoría de los fabricantes recomiendan encerar de 3 a 5 veces al año en condiciones normales. La mayoría de los motoristas no se depilan con tanta frecuencia, ya sea por el esfuerzo que supone o porque piensan que la cera sigue funcionando.

    Además, la cera se derrite a poco más de 100°F. Si vives en una zona con temperaturas más altas (90°F o más) o tienes una moto de color más oscuro, tu moto apenas está siendo protegida contra el calor del sol, por lo que ciertamente no es rival para las superficies de alta temperatura, como el escape de tu moto. Funciones como el bloqueo de los rayos UV y la resistencia a las manchas son las primeras en fallar y luego siguen disminuyendo bruscamente. Esto significa que su moto está siendo expuesta a los elementos y la superficie se deteriora lentamente, se desvanece y se corroe.

    El revestimiento cerámico para motocicletas Glidecoat protege y preserva la integridad de la superficie de su moto, superando con creces los productos de cera tradicionales. Una vez aplicado el revestimiento, se adhiere directamente a la superficie de su moto para crear una capa dura de larga duración. Esto permite que el revestimiento proteja su moto hasta 3 años (más tiempo dependiendo del almacenamiento, el uso y el cuidado posterior). Nuestro revestimiento cerámico también es resistente a temperaturas de hasta 1100 °F. Esto permite revestir las superficies de alta temperatura, como las partes expuestas del motor y los tubos de escape, protegiéndolas de las manchas, los daños causados por los rayos UV y la corrosión.

    Se puede aplicar a todas las superficies:
    En comparación con un automóvil, que es en gran parte superficies pintadas con revestimiento transparente, una motocicleta tiene una mayor variedad de superficies que necesitan ser protegidas – paneles pintados, tanques, molduras de plástico, vidrio, horquillas cromadas, llantas y marcos de metal. Se necesita un recubrimiento que sea lo suficientemente versátil como para afrontar los retos de cada una de estas superficies.

    Además, muchas de estas superficies, como los componentes expuestos del motor o los tubos de escape, son superficies de alta temperatura. El revestimiento cerámico para motocicletas Glidecoat está diseñado para soportar altas temperaturas (1100°F/600°C) y puede utilizarse para proteger incluso las superficies más calientes.

    Mantenimiento:
    Una de las interpretaciones erróneas más comunes de un revestimiento cerámico es que no necesitan mantenimiento, o que su motocicleta no se ensuciará si tiene un revestimiento cerámico. Esto no es así. Dicho esto, el principal beneficio de tener un revestimiento cerámico es que su continuo mantenimiento es mucho más fácil y eficaz (con menos esfuerzo) que el uso de una cera o sellador tradicional. Todos estamos de acuerdo en que si se dedica menos tiempo a la limpieza y más a la conducción, se gana.

    Debido a que el revestimiento cerámico crea una superficie extremadamente hidrofóbica y súper resbaladiza, la mayoría de las manchas y contaminantes se limpian fácilmente de la superficie con un rápido enjuague. Ya no necesitará productos químicos y jabones agresivos para limpiar su moto. Basta con lavarla con un jabón suave de pH neutro, como nuestro Glidecoat Nano Wash o Glidecoat Ceraglo, y una manopla de microfibra o un cepillo de cerdas suaves.

    Además de la facilidad de limpieza, el revestimiento durará 3 años (más, dependiendo del almacenamiento y el cuidado posterior), lo que supone entre 10 y 15 veces más que la cera. Esto significa que se pierde mucho tiempo puliendo y aplicando cera.

    ES MUY IMPORTANTE QUE SIGA LAS INSTRUCCIONES PROPORCIONADAS CON TODOS LOS PRODUCTOS GLIDECOAT.

  • Coverage

    Coverage

    We recommend a minimum of 2 coats applied to most areas of your bike’s surface. In heavily exposed or high temperature areas of the bike, we suggest 3 coats. A 30ml bottle of coating will allow you to cover up to 36 SQFT with 2 coats.

    If you require recommendations from our team based on your specific needs, please do not hesitate to reach us at (561) 290-0165 and we will be glad to assist.

  • Benefits

    Benefits

    The benefits of Glidecoat’s Motorcycle Ceramic Coating include:

    • Hard-barrier: Once the coating cures, it forms a hard barrier to protect your bike from minor abrasions.
    • Bonds with the surface: Our coating actually fills the pores of the surface allowing the coating to bond with the surface. This prevents the coating from washing away or removal from abrasion.
    • Multi-surface protection: Can be applied to paint, plastic, chrome, metal, glass and more. This allows you to protect all of the hard surfaces of your bike including the paintwork, exhaust, chrome, forks, panels, frame and rims.
    • Reflects UV: The coating reflects harmful UV which prevents sun damage, fading and oxidization.
    • Long-lasting: The coating will last up to 36 months even in extreme conditions – 10 times longer than wax, Teflon coatings or paint protection coatings.
    • Heat resistant: Unlike wax, our ceramic coating can withstand temperatures up to 1100°F (600°C) and is not susceptible to heat and will not melt or evaporate.
    • High-gloss finish: The coating creates an ultra high-gloss finish which shines better than new. Especially important for chrome surfaces that dull easily.
    • Clear and vibrant: The ceramic coating remains clear and will not yellow over time. This ensures the colors and graphics will stay vibrant.
    • Easy to clean: The coating creates a super smooth hydrophobic surface which repels contaminants. Simply spray down and wipe dry to remove any bugs or road dirt.
    • Easy re-application: Future coats can be applied without having to remove previous ceramic coating applications.
    • Increased visibility: Coating the glass of your motorcycle or the visor of your helmet reduces the build up of road contaminants and bugs and because it is hydrophobic, water beads off, increasing visibility in the rain.
    • Cost: Over the life of the coating, ceramic is much less expensive than paint and corrosion repairs. Also reduces amount of wax and cleaning products required to maintain your motorcycle.
  • Application Instructions

    Application Instructions:

    IT IS VERY IMPORTANT THAT YOU FOLLOW THE INSTRUCTIONS SUPPLIED WITH ALL GLIDECOAT PRODUCTS.

    • Prior to starting the Ceramic Coating application process, ensure that the surface of your motorcycle has been fully prepped. This includes polishing and compounding and removing any oxidization or making any repairs necessary. The ceramic coating will lock in any imperfections on the surface of your motorcycle, so it is important that you are happy with the surface before coating.
    • Before coating, ensure the engine and exhaust are cool to the touch. Remove the seat, saddlebags, or any surfaces that you don’t wish to get wet. Cover any other areas that can’t easily be removed to protect them.
    • Pre-rinse the bike with water to remove any lose dirt. This helps minimize the chances of adding swirls or scratches to the surface.
    • Thoroughly wash the entire motorcycle using Glidecoat Nano Wash. Start by cleaning the rims and tires using the two-bucket method.
    • Once the bike has been cleaned and rinsed, we recommend a Glidecoat Iron Remover treatment to remove all contamination from the surface of the paint. This must be done while the bike is wet. Let the Iron Remover dwell on the surface for 5-10 minutes and then soap wash the bike one more time.
    • Thoroughly dry the bike using a clean microfiber towel. You may also use a leaf blower to expedite the dry process and help dry hard to reach areas. Always dry completely and never leave to “air” dry. Tap water contains minerals that may leave deposits or water spots when left to dry.
    • After the motorcycle’s surface has been fully prepared – remove oxidization, contaminants, and wash, clay bar – Start by wiping down the area to be coated with Glidecoat Surface Wipe. This product acts as a decontaminant removing any polish, compound or other products left on the surface. This allows the ceramic coating to penetrate into the pores.
    • Apply a dime-sized drop of the product to the center of the application sponge. Apply in 2’ by 2’ areas, using a cross-hatch pattern. Once applied, immediately buff with a microfiber towel to remove any excess and then re-buff with a separate clean microfiber.
    • Do not wait after application across that 2’ x 2’ area. Immediately buff or the surface will become difficult to buff and cause streaking.
    • Once the first microfiber becomes damp or causes streaking, replace it immediately. Do not apply in direct sunlight. Ideal application conditions should have an air temperature between 50°F (10°C) up to 90°F (32°C). The less humidity the better.
    • Apply to all areas of the bike. Apply a second coat after 1 hour.
    • In heavily sun exposed or high temperature areas of the bike, we suggest 3 coats.
  • Maintenance Guide

    Ceramic coatings have become increasingly popular over the past few years, but even with the popularity of ceramic coatings there is still a lot of misinformation about coatings and what they can do.

    Ceramic coatings are one of, if not the best product to protect and preserve the integrity of your surface, far superior to traditional wax and sealants. One of the most common misinterpretations of a ceramic coating is that they are almost maintenance free, or your boat/car/RV/motorcycle will not get dirty if it has a ceramic coating. That is simply not the case.

    While ceramic coatings are extremely durable, they require ongoing maintenance to ensure that you are getting the full benefits and protection out of your ceramic coating. With that being said, the main benefit of having a ceramic coating is that your ongoing maintenance is much easier and more effective (with less effort) than using a traditional wax or sealant.

    The following will explain how to properly maintain your ceramic coating to ensure you are getting the most out of your ceramic coating, and properly protect your investment.

    INITIAL APPLICATION MAINTENANCE
    After the application of our Ceramic Coating, it is important to let the coating fully cure before getting the wet. A full cure of our ceramic coatings is between 24-48 hours. If the boat/car/RV/motorcycle gets wet or rained on during the curing process, dry as soon as possible, and avoid leaving water to air dry to prevent potential water spots on the surface.

    Allow a minimum of 48 hours before washing to ensure the coating has fully cured.

    ONGOING MAINTENANCE
    After the coating has fully cured, we recommend the ongoing maintenance of rinsing (and drying) regularly, bi-weekly washes, and spot cleaning as needed.

    Ongoing maintenance is an important factor in ensuring that you get the most benefits from your ceramic coating. If a coating is too dirty, this layer of contamination (salt, dirt, bird droppings, water spots) will diminish the stain resistance and hydrophobic properties of the ceramic coating, making it more difficult to clean, defeating the main purpose of a ceramic coating.

    Here are some general guidelines for ongoing maintenance of your ceramic coating:

    • Rinse regularly to remove contaminants from the surface. We highly recommend drying after rinsing, and avoid letting the water air dry, which may cause water spots. If you cannot access the area to dry, we recommend using a stream of water (not a spray nozzle) to remove contaminants while not leaving excess water on the surface that could cause water spots.
    • Bi-weekly washes (every two weeks) with Glidecoat Nano Wash or Glidecoat Ceraglo. Avoid using high pH soaps such as Dawn dish soap, or soaps that contain heavy cleaners or degreasers. These soaps won’t harm the coating after a few uses, but continual use of aggressive soaps and cleaners will expediate the wear of the top layer of coating. This will diminish and reduce the protective qualities of the ceramic coating, as well as reduce the longevity of the coating. Glidecoat Ceraglo is the perfect after care soap for you ceramic coating. Ceraglo is a polymer infused soap designed to increase the gloss of the surface while leaving a layer of protection on top of the ceramic coating to promote the longevity.
    • Avoid using stiff bristled brushes or abrasive washing tools.
    • Use a microfiber wash mitt or a soft bristled brush when washing.
    • Dry with a microfiber drying cloth or a clean chamois.

    SPOT CLEANING MAINTENANCE
    In between your bi-weekly washes you may need to do some spot cleaning. Whether it’s salt build up, water spots from the rain, or bird droppings, we recommend cleaning them as you see them to make your ongoing maintenance that much easier.

    Here are some general guidelines for spot cleaning:

    • For excess salt buildup we recommend using Glidecoat X-Salt to safely remove the salt without harming the ceramic coating. Simply spray X-Salt on the surface, allow it to dwell for 5-10 minutes, then rinse it off. X-Salt can also be added to your wash bucket with Glidecoat Nano Wash or Glidecoat Ceraglo to help remove stubborn salt buildup while you wash.
    • If you are having issues with hard water spots we recommend using Glidecoat WaterSpot Remover to safely remove hard water spots without harming the ceramic coating. Simply spray Glidecoat WaterSpot Remover onto the surface, wipe it in with a microfiber cloth, allow it to dwell for 2-3 minutes then wipe it off with a clean microfiber cloth.
    • When spot cleaning bird droppings or small stains we recommend using a waterless wash of <Glidecoat Surface Wipe with a microfiber cloth. Avoid using excessive force when removing stains.

    QUARTERLY MAINTENANCE
    In addition to ongoing maintenance and spot cleaning, ceramic coatings benefit from a maintenance spray every 3-4 months in southern states or once a season in northern states, such as <Glidecoat’s Shine and Shield Ceramic Spray. Shine and Shield will enhance the shine and hydrophobic effect of the surface, while adding an additional layer of protection on top of the ceramic coating to promote longevity.

    Shine and Shield is a simple spray on, wipe off application.

    Here are some general guidelines for applying Shine and Shield for quarterly maintenance:

    • Shine and Shield can be applied as needed to add gloss and water beading to the surface.
    • Do not apply Shine and Shield to a dirty surface, always clean/wash the area first before applying.
    • Shine and Shield can be applied to a wet surface, allowing you to dry the surface while leaving some protection behind.
    • We recommend using two microfibers when applying Shine and Shield, using the first microfiber to buff the surface while using a second clean microfiber to ensure the surface is smooth and uniform.
    • Shine and Shield can be layered with multiple coats for enhanced protection, allow a minimum of 30 minutes between each coat.

    ANNUAL MAINTENANCE
    An annual maintenance typically consists of a decontamination wash with Glidecoat Iron Remover to remove contamination from the surface that could be impacting the hydrophobic properties of the ceramic coating. After the Iron Remover, wash with Glidecoat Nano Wash or Glidecoat Ceraglo. Inspect the coated areas to ensure that the ceramic coating is holding up as expected. If any areas are not beading water, but still have a good shine, apply Shine and Shield to restore the hydrophobic activity on the surface.

    If any of the high sun exposed areas have significantly diminished in gloss it may require a light polish to restore the shine and have one additional coat of the ceramic coating applied.

  • Reviews (0)

    Reviews

    There are no reviews yet.

    Be the first to review “Revestimiento Cerámico para motocicletas”

    Your email address will not be published. Required fields are marked *

  • Return Policy & Disclaimer

    Return Policy
    We guarantee to refund any item you are not completely happy with when you return it to us in a saleable condition within 14 days of receipt. When issuing a refund we will need to see proof of your original purchase. Refunds will be credited to your original method of payment. Please note, this policy only applies to retail customers.

    For safety reasons, we cannot offer refunds on products that have been opened or used unless they are faulty or unfit for purpose. Please note, if you purchased our products through another reseller, you will need to return the products to the original place you purchased them.

    How do I make a return?
    Returns are simple and easy. If you need to return an item simply send the product(s), a letter as to why you are returning the products (please include contact details) and your original proof of purchase to:

    Glidecoat
    931 Village Blvd. Unit 905-121
    West Palm Beach, FL 33409

    What about my delivery charge?
    If we have made a mistake on an item sent to you or it is faulty, damaged, of unsatisfactory quality, we will refund the delivery charges you have paid to receive that item unless it was sent to you with other items which you are not returning.

    Disclaimer
    Glidecoat a division of Onan Technologies Inc.’s maximum liability for or with respect to any damages of any kind to any person, property or otherwise, caused to any Customer or any other person as a result of or with respect to any proven breach of any express or implied warranty with respect to any Product; misrepresentation with respect to any Product; Product error, failure or malfunction; formula, engineering or design error; manufacturing or packaging error; labeling error; Product failure to perform; or any other act or omission of any kind whatsoever with respect to any Product, shall be limited the price paid by the Customer for the Product at the time of original purchase (not including shipping, handling, sales taxes or installation services); and Product purchase price refund shall be Customer’s only claim or remedy arising therefrom. IN
    ADDITION TO AND WITHOUT LIMITATION OF THE FOREGOING, GLIDECOAT SHALL NOT BE LIABLE UNDER ANY RULE OR THEORY OF LAW TO ANY CUSTOMER OR ANY OTHER PERSON FOR (A) INCIDENTAL, CONSEQUENTIAL, SPECIAL, PUNITIVE, OR EXEMPLARY DAMAGES OF ANY KIND, INCLUDING BUT NOT LIMITED TO LOSS OF REVENUES, LOSS OF PROFITS, LOSS OF BUSINESS, OR OTHER ECONOMIC DAMAGES, OR (B) ERRORS MADE IN THE HANDLING, STORAGE OR INSTALLATION OR APPLICATION OF ANY PRODUCT, REGARDLESS OF WHETHER ONAN WAS ADVISED OF, KNEW OR OUGHT TO HAVE KNOWN OF THE POSSIBILITY OR RISK OF SUCH LOSSES OR DAMAGES.